A spread axle trailer is a trailer whose two rear axles sit far apart, typically about 10 ft center to center, instead of close together in a sliding or fixed tandem. That extra spacing changes how the axle group is counted at the scale. Close together, two axles are a tandem capped at 34,000 lb on the Interstate. Spread past 96 inches, they are two single axles, and the pair can carry up to 40,000 lb. That 6,000 lb of headroom is the reason spread axle flatbeds and reefers exist.
What is a spread axle trailer?
| Tandem | Spread axle | |
|---|---|---|
| Axle spacing | More than 40 in, up to 96 in | More than 96 in, usually about 10 ft |
| How the scale counts it | One tandem group | Two single axles, checked by the bridge formula |
| Federal limit on the group | 34,000 lb | Up to 40,000 lb at 10 ft |
| Sliding axles | Common on vans | Rare; spacing is usually fixed |
| Turning | Tighter, less tire scrub | Wider, more tire scrub |
| Typical trailers | Dry vans, most reefers | Flatbeds, some reefers and step decks |
The 40 to 96 inch tandem definition comes from 23 CFR 658.5. Anything spread wider is no longer a tandem under that rule.
Spread axle trailer weight limits: the math
Federal law sets the single axle limit at 20,000 lb and the tandem limit at 34,000 lb, with 80,000 lb gross on the Interstate (23 CFR 658.17). For groups of axles it uses the bridge formula:
W = 500 × (L × N ÷ (N − 1) + 12N + 36)
W is the weight allowed on the group, L the distance in feet between the outer axles, and N the number of axles. For two axles (N = 2), it simplifies to W = 500 × (2L + 60).
- At 97 inches (8.08 ft): 500 × (16.17 + 60) = 38,083, rounded to 38,000 lb. FHWA's bridge formula guide uses this same example.
- At 9 ft: 500 × (18 + 60) = 39,000 lb.
- At 10 ft: 500 × (20 + 60) = 40,000 lb.
- At 11 ft the formula gives 41,000 lb, but each axle is still capped at 20,000 lb, so the pair stays at 40,000 lb. Spreading wider than 10 ft gains nothing federally.
These are our calculations from the federal formula. Your load must also pass the bridge formula on every other axle group of the rig, and the 80,000 lb gross limit.
What the extra weight actually gets you
A spread axle does not raise your 80,000 lb gross on the Interstate. What it raises is how much of that weight the trailer axles may carry.
- Steer axle
- 11,500 lb
- Drive tandem (limit 34,000)
- 32,500 lb
- Trailer: spread axle at 10 ft (limit 40,000)
- 36,000 lb
That room matters for freight that cannot be moved forward on the deck: a steel coil, a machine, a heavy crate that must sit over the rear. On a tandem you would slide the axles or shift the load to get the trailer group legal. With a spread axle, the trailer group can carry the extra. Check your own numbers in the axle weight calculator.
Spread axle trailer weight limits by state
The federal numbers apply on the Interstate. On state roads, states set their own axle and gross limits, and some write their own rules for spread or split axles, or carry older "grandfathered" limits. Before you book a heavy load through a state you do not run often:
- Find the state DOT's legal weight page or truck manual.
- Look for how it treats two axles more than 96 inches apart.
- Check bridge and seasonal postings on the route.
- If the load is over legal anywhere on the route, it needs a permit, and that changes the job.
Uses: spread axle flatbed, reefer and step deck
- Flatbeds. The most common spread axle trailer. Steel, coils, lumber and machinery put a lot of weight in a short space.
- Reefers. Some carriers spec spread axle reefers for heavy produce and meat loads that run close to the limit.
- Step decks. Heavy equipment on the lower deck often lands right over the axles.
- Dry vans. Rare. Most van freight is bulky before it is heavy, so the sliding tandem is the better tool.
The trade-offs
Tire scrub and turning. Two axles 10 ft apart cannot both follow a tight curve. The tires drag sideways in yards, docks and city turns, which wears tread and loads the suspension. Alignment matters more than on a tandem; see truck trailer alignment.
No slide. Most spread axles are fixed, so you cannot slide the axles to balance the load the way you can on a van. Weight distribution has to be planned at the dock.
Tight docks and yards. The longer wheelbase needs more room to back and turn. Some shippers with cramped lots ask for tandem equipment.
Storage and resale. A spread axle trailer is specialized, so it suits carriers who run heavy freight week after week. Where to park it between runs is covered in truck trailer storage.
Should you run a spread axle?
Run one if your freight is regularly heavy and concentrated: steel, coils, machinery, heavy produce. Skip it if you haul light, bulky freight or live in tight city docks, where a tandem is easier and cheaper on tires. Empty spread axle flatbeds are sometimes moved stacked on another trailer when relocating equipment. For the trailer side of a van fleet, start with the dry van trailer guide, and for every trailer type in one place, see types of truck trailers.
Questions carriers ask
01What is a spread axle trailer?
A semi trailer whose two rear axles are mounted far apart, commonly around 10 ft center to center, instead of side by side in a tandem a few feet apart. The wider spacing spreads the load over a longer stretch of road and bridge, which is why it may be allowed more weight on the axle group.
02What is the weight limit on a spread axle trailer?
Federally, two axles more than 96 inches apart are not a tandem, so the 34,000 lb tandem limit does not apply. Each axle is held to 20,000 lb, and the pair to what the bridge formula allows for their spacing: 40,000 lb at 10 ft. Gross weight is still 80,000 lb on the Interstate, and states set their own rules on other roads.
03Is a spread axle the same as a split axle?
People use both names for the same setup: two trailer axles split far apart instead of grouped as a tandem. Some states write their own definition, so on a permit or state weight table check how that state classifies the spacing.
04Do spread axle trailers wear out tires faster?
They can. In tight turns, axles that are far apart cannot both follow the curve, so the tires drag sideways. That scrub shows up as faster wear on the tires and more stress on the suspension, especially on trailers that run a lot of city and yard miles.
SOURCES
- 23 CFR 658.5 (via Cornell LII): Tandem axle weight: two or more consecutive axles whose centers are more than 40 inches and not more than 96 inches apart; federal tandem limit 34,000 lb on the Interstate (checked 2026-10)
- eCFR, 23 CFR 658.17: Federal weight limits on the Interstate: 80,000 lb gross, 20,000 lb single axle, 34,000 lb tandem, bridge formula (checked 2026-10)
- FHWA, Bridge Formula Weights (FHWA-HOP-19-028, August 2019): W = 500(LN/(N-1) + 12N + 36); two axles 97 inches apart may carry 38,000 lb; two tandems 36 ft or more apart may carry 34,000 lb each (checked 2026-10)
SOURCE: Primary sources listed above, checked on the dates shown.